Tydligen har rätt många teknikwebbplatser som testat kortet uppmätt samma sak, någon har även köpt in retail-kort och fått samma resultat.
Sedan finns en tråd på reddit som pekar på att PCI 3.0 tillåter 300 W, efter liten egen efterforskning verkar det faktisk som standarden tillåter upp till 1000 W per "slot". Tyckte först det var väldigt konstigt att AMD inte direkt bara pekade ut detta och på så sätt få det hela att blåsa förbi.
Är ingen expert på PCIe och absolut inte på de elektriska/mekaniska bitarna, men PCIe standarden säger faktiskt inget om det elektriska men den pekar på en annan standard som kallas Electro-mechanical specification.
Det som är lite luddigt här är exakt vad en "slot" är. Reddit-tråden är nu uppdaterad och sett flera peka på samma tolkning. Power limit för en "slot" är totala effekten kortet som sitter där få dra, men det är summan av det som tas från moderkortet och övriga 6/8-pinnars kontakter. Så PCIe 3.0 kan hanterar kort som totalt drar 1000 W, men det är inte tillåtet att dra mer än 75 W från moderkortet, inte mer än 75 W från varje enskild 6-pinnars kontakt och inte mer än 150 W från varje enskild 8-pinnars kontakt.
Electro-mechanical specification har ett förtydligande exempel som säger
"For graphics, the power level assigned will be dependent on the platform’s support of the PCI Express x16 Graphics 150W-ATX Specification, Revision 1.0 (including the supplemental power cable)."
Du är medveten om att din avslutande text refererar till ett separat dokument/specifikation, även den första när det gäller PCI-E (Rev 1.0)?
På den tiden så drog nära på inget grafikkort i närheten av 150W så där var inte tagit höjd för mer.
Edit 1: Senare spec tar hojd för mer än 150W!
Edit 2: Ett kort år om jag inte missminner mig dra mer än 10W vid initial handskakning där kortet ska ange sitt effektbehov = vill det ha mer än vad moderkortet är designat för så förvägras kortet start!
Sen begränsningen av max effekt är inte i första hand avhängigt PCI-E bussen, då den ursprungliga begränsningen är satt för passivt kylda PCI-E kort och deras förmåga att bli av med effekten.
PCI-E x1 10W för halvlängdskort/lågprofil och 25W för fullängdskort
PCI-E x4/x8 25W för alla
PCI-E x16 75W för alla utom lågprofil som begränsas till 25W
Allt enligt "PCI_Express_CEM_1.1"... från vilket nedanstående är klippt, även här refereras till "PCI Express x16 Graphics 150W-ATX Specification, Revision 1.0" som i sig INTE tillåter något kort att dra över 150W :
The power limits for respective connector widths, x1, x4/x8, and x16, represent the add-in card and
5 system capacity to provide cooling for the slot. The 10 W limit assumes natural convection cooling
in a system that provides air exchanges. The 25 W and above add-in card power limits assume that
sufficient cooling is provided to the slot by the cards in the present chassis environment. In general,
the power limits above assume a chassis environment with a maximum internal temperature of 55ºC
on the primary component side of the add-in card and natural convection cooling in a system that
10 provides air exchanges. Implementations of other chassis environments should pay special attention
to system level thermal requirements.
PCI Express allows for higher maximum power for graphics cards than AGP. In case such a
graphics card is used in a system, implementers should pay special attention to system level thermal,
acoustic, structure, and power delivery requirements. To insure optimum performance, it is
15 recommended that the system designer refer to the PCI Express Graphics Card Thermal and Mechanical
Guideline for Desktop Systems.
IMPLEMENTATION NOTE
Software Update of the Slot Power Limit
System firmware must update the slot power limit to the system's allocated value for the PCI
20 Express add-in card (e.g., graphics) and ensure the completion of this update prior to invoking the
option ROM for that add-in card's PCI Express function. If the initial slot power limit value is set
by hardware initialization, then any attempt by software to change that value must be verified by that
software prior to initializing the add-in card. Subsequent updates by the system firmware or
operating system software, if any, may only increase the slot power limit value. However, after a
25 card is reset, the initial slot power limit value may be lower than the previous value. The maximum
power level for an add-in card must be assigned by the system firmware during PCI Express
configuration. For graphics, the power level assigned will be dependent on the platform’s support
of the PCI Express x16 Graphics 150W-ATX Specification, Revision 1.0 (including the supplemental
power cable).
Engineer who prefer thinking out of the box and isn't fishing likes, fishing likes is like fishing proudness for those without ;-)
If U don't like it, bite the dust :D
--
I can Explain it to you, but I can't Understand it for you!